Maytag

Maytag Appliances We Repair

Maytag built its reputation on durability, and Denver homeowners who chose this brand tend to hold onto their appliances for a long time. That longevity means older Bravos, Centennial, and Neptune models are still in service across the metro, alongside current production units. We service the full Maytag lineup: top-load and front-load washing machines, dryers, french door and side-by-side refrigerators, dishwashers, ovens, and ranges.

Worth knowing: Maytag is owned by Whirlpool Corporation and shares platforms and parts with several other brands in the Whirlpool family. If you also own a Whirlpool, Amana, or KitchenAid appliance, we service those too.

Common Maytag Problems We Fix

Maytag Dryer Not Heating

Maytag dryer not heating is our most common Maytag repair call. The drum turns and the cycle runs to completion, but clothes come out damp. On Maytag electric dryers, a burned heating element or a tripped thermal fuse is almost always responsible. A Maytag washer not turning on at all is a separate symptom that points to the thermal fuse or the control board rather than the heating circuit, and we address both during the same visit if needed. On Maytag gas dryers, the igniter fails to reach the temperature needed to open the gas valve, or a faulty gas valve coil stops the burner entirely. Both gas and electric models share the thermal fuse as a common failure point after an overheating event.

Specific sub-lines have patterns worth knowing. Maytag Bravos XL dryer not heating is one of the most frequent calls we receive for this platform, typically pointing to the thermal fuse or heating element. Maytag Bravos dryer not heating on earlier Bravos models follows the same pattern. Maytag Centennial dryer not heating is equally common and traces to the same components. Maytag front load dryer not heating calls on older Neptune models more often involve a failed heating element combined with airflow restriction from a partially blocked duct. We test the full heating circuit and check the duct on every dryer visit.

Maytag Washer Not Spinning

A Maytag washer not spinning leaves the load soaked and heavy. On top-load Maytag washers, a failed lid switch is the most common cause. The machine will not enter the spin cycle if it does not detect the lid as closed. A worn drive belt or a failed motor coupling produces the same symptom with different diagnostic steps. Maytag Bravos XL washer problems frequently involve the lid lock assembly, which combines the switch and the locking mechanism into one unit that fails as a whole. Maytag Centennial washer not spinning calls most often trace to the same lid lock fault or a failed actuator.

Maytag Bravos washer problems in general also include control board faults that prevent spin without triggering a clear error code. If the washer fills and agitates normally but stops before the spin cycle, that pattern points to the lid lock or the board rather than the motor. Our washer repair page covers additional detail on how we approach these calls.

Maytag Washer Not Draining

Maytag washer not draining leaves standing water in the drum at the end of the cycle. The most common causes are a clogged drain pump filter, a blocked drain hose, or a failed drain pump motor. A Maytag washer that won’t drain and won’t spin together usually points to the pump rather than a separate spin fault, because the machine will not attempt to spin until the water is gone. Maytag washer not spinning clothes dry is a related symptom: the machine technically spins, but residual water that was not pumped out makes clothes feel wetter than they should be after the cycle. We test the pump, the filter, and the drain hose on every washer not draining call.

Maytag Washer Leaking

A Maytag washer leaking from the bottom is usually one of three things: a cracked or loose tub-to-pump hose, a failed water inlet valve that drips during fill, or a worn door boot seal on front-load units. On older top-load models, a degraded tub seal is less common but does occur. A small leak that is ignored tends to grow. Water reaching the motor or the control board creates a significantly more expensive repair than the original leak would have been.

Maytag Ice Maker Not Working

Maytag ice maker not working covers several possible causes depending on the refrigerator configuration. A Maytag refrigerator ice maker that stops producing is most commonly caused by a failed water inlet valve, a frozen water supply line, or a faulty ice maker module that has stopped cycling. On side-by-side models, inlet valve failure around the 5-8 year mark is the most typical pattern. On french door configurations, a temperature sensor reading incorrectly can also shut down ice production while the refrigerator itself cools normally. We carry the most common inlet valves and ice maker assemblies for Maytag refrigerators.

Maytag Refrigerator Not Cooling

A Maytag refrigerator not cooling requires a systematic check of both the mechanical and control systems. If the freezer is still cold but the fresh food section is warm, the evaporator fan motor has usually failed or the defrost system has iced over the coils. If neither section is cooling, the compressor or a refrigerant issue is more likely. Dirty condenser coils are a common secondary cause that accelerates failure on units that have not been serviced in several years. For freezer-specific issues, see our freezer repair page.

Maytag Dishwasher Not Draining

Maytag dishwasher not draining leaves standing water in the tub after the cycle ends. A clogged drain filter is the most common and easiest fix. A failed drain pump motor or a blocked drain hose are the next most frequent causes. As with other brands, an incorrectly installed drain hose that is not looped high enough under the counter allows sink backflow to mimic a drainage fault when nothing is actually broken. We inspect the installation and the components together on every dishwasher not draining call.

Why Denver Homeowners Choose Wilson & Myers for Maytag Repair

The legend of the Maytag repairman who never gets a call is a good story, but these appliances do eventually need service, and when they do it helps to have a technician who knows the platform. Our technicians work on Bravos, Centennial, and standard models regularly across Denver Metro. If you need Maytag repair near me in Denver, Wilson & Myers is the answer. Insured. OEM parts only. A 100-day labor warranty on every repair. Book online or call a pro for same-day availability.

We also service Whirlpool, GE, Samsung, LG, KitchenAid, and all other major brands. Full list on our appliance brands page.

Service area: Denver, Aurora, Lakewood, Arvada, Westminster, Thornton, Littleton, Englewood, Boulder, Centennial, Parker, Highlands Ranch, Broomfield, Golden, Morrison, and surrounding communities.

Maytag Appliance Repair FAQ

1. Who repairs Maytag appliances in Denver?

Wilson & Myers services Maytag appliances throughout Denver Metro, including Bravos XL, Centennial, and Neptune models. Whether you need Maytag appliance repair near me or service on a specific appliance, same-day availability is most days. Book online or call a pro to check scheduling.

2. Do you repair older Maytag models like Bravos, Centennial, and Neptune?

Yes. These are among the most common Maytag units we see in Denver Metro. Parts availability for Bravos XL and Centennial is good, and most repairs on these platforms are straightforward. Neptune front-load units are older but we still service them when parts are available.

3. My Maytag washer won’t drain and won’t spin. Are those two separate problems?

Usually not. When a Maytag washer won’t drain and won’t spin at the same time, the drain pump is almost always the root cause. The machine will not attempt to spin until it has pumped out the water, so what looks like two failures is typically one. We test the pump first on these calls.

4. Is Maytag related to Whirlpool? Does that affect repair?

Yes. Whirlpool Corporation has owned Maytag since 2006. The two brands share platforms and many components, which means parts availability is generally good and our technicians who work on Whirlpool units apply the same knowledge to Maytag. See our Whirlpool repair page for more on that platform.

5. Is it worth repairing an older Maytag appliance?

Usually yes. Maytag appliances are built to last, and a single component failure on a sound unit is almost always cheaper to fix than to replace. Our technicians give you a straight cost-versus-replace assessment before any work begins. For Maytag washer repair near me or Maytag dryer repair near me across Denver Metro, same-day availability is most days.